
Boise, ID
Concrete Cutting in Boise
A 100-foot cutting job in Boise runs about $990–$1,975, and single cores start around $40–$120 a hole.
- Slab sawing for trenches and removals
- Core holes for plumbing, electrical and HVAC
- Wall sawing for doors and egress windows
Slab sawing prices in Boise
Typical ranges from cost guides and a Boise estimate, not quotes. Most cutters charge a $150–$400 trip minimum, and a permit can add about $65–$130.
What to have ready
- The address, and whether the slab is indoors or outside
- How thick the slab is, or where an edge shows its depth
- How many feet of cut, or the trench length and width
- Whether there is rebar, mesh or radiant heat tubing in the slab
- How close the truck can park and where water can drain
Locates, right-of-way and slurry in Boise
A trench cut through a slab ends in digging, and Idaho counts moving any earth or rock in the ground as excavation. Request a locate through Digline 2 to 10 business days ahead, white-line the trench, and keep the work inside the 3 weeks the marks stay valid.
Cuts in a curb, sidewalk or street are inside the Ada County Highway District's right-of-way, which takes an ACHD right-of-way use permit and a licensed, bonded contractor. A driveway change on your own lot needs Planning and Zoning approval.
Wet sawing makes gray slurry. Boise makes it illegal to dump substances into a storm drain, so outdoor cuts near a gutter need the inlet blocked and the slurry picked up.
Core Drilling in Boise
4-inch cores about $40–$120 a hole; 6 to 12 inch $150–$600
Typical ranges from cost guides, not quotes. A $150–$400 trip minimum is common, so one hole and five holes can cost about the same.
Wall Sawing in Boise
$8–$25 a foot; egress window cuts $350–$700 in Boise
Typical ranges from cost guides and Boise estimates, not quotes. A doorway is about 20 feet of cut around its edges, and trip minimums of $150–$400 apply.
Cutting concrete in Boise
Most calls here are a plumber's trench through a garage or basement slab, a run of cores for a commercial tenant finish, or a new doorway or egress window in a foundation wall. Boise estimates put a 100-foot cutting job near $1,400 at a local labor rate of about $103 an hour.
Openings need paperwork first. The City of Boise lists new door and window openings, and widening an existing one, as permit work, so have the permit in hand before the saw is booked.
Once a cut goes through the slab into the soil, Idaho treats it as excavation. Request a locate 2 to 10 business days ahead, and plan the work inside the 3-week window the marks stay good.
- $103/hr
- Boise labor rate What local estimates assume for a cutting crew, before markup.
- 2–10 days
- Idaho 811 notice Business days before you dig under a slab, through Digline.
- $350–$700
- Egress window cut The cutting share of a Boise egress window in a concrete foundation.
- 30 in
- Largest local cores At least one Boise coring crew drills holes that wide.
Areas served
We cover Boise and the Treasure Valley towns local cutting crews already work, including Meridian, Garden City, Eagle, Star, Kuna, Nampa and Caldwell. Work on a street, curb or sidewalk in Ada County also needs an ACHD right-of-way permit.
- Boise
- Meridian
- Garden City
- Eagle
- Star
- Kuna
- Nampa
- Caldwell
Boise questions
Do I need a permit to cut a doorway in a concrete wall?
In Boise, yes. New door or window openings and widened openings are on the city's permit list; questions go to (208) 608-7070.
Do I need an 811 call for cutting inside a building?
If the cut or core goes through the slab into the ground below, it fits Idaho's definition of excavation, so request a locate first.
Is there a minimum charge?
Usually. Cutters commonly set a trip minimum of $150–$400, so a single small hole costs about the same as a few.
Can I cut back my driveway without a permit?
Boise doesn't require a building permit for a driveway, but it does need Planning and Zoning approval, and anything past your property line needs an ACHD permit.
Why is a short cut priced like a long one?
Trip minimums of $150–$400 cover the setup, so a 10-foot cut can cost the same as a 30-foot one.
How long does a typical job take?
Boise estimates plan about 8 hours of crew time for 100 feet of cutting.